05-SDRAM: Arbitration

SDRAM 仲裁

1. state
2. sdram_cmd_reg: 初始化、写操作、读操作、Since the refresh module instruction coming,Need to internal usesdram_cmd接收,
   Then respectively output forsdram_cs_n、sdram_ras_n、sdram_cas_n、sdram_we_n
3. aref_en: The current state of arbitration stateARBIT,且aref_req=1 （依赖ARBIT、aref_req）
4. wr_en: The current state of arbitration stateARBIT,且wr_req=1 （依赖ARBIT、wr_req）
5. rd_en: The current state of arbitration stateARBIT,且rd_req=1 （依赖ARBIT、rd_req）

设计文件

// SDRAM 仲裁
// 1. state
// 2. sdram_cmd_reg: 初始化、写操作、读操作、Since the refresh module instruction coming,Need to internal usesdram_cmd接收,
// Then respectively output forsdram_cs_n、sdram_ras_n、sdram_cas_n、sdram_we_n
// 3. aref_en: The current state of arbitration stateARBIT,且aref_req=1 （依赖ARBIT、aref_req）
// 4. wr_en: The current state of arbitration stateARBIT,且wr_req=1 （依赖ARBIT、wr_req）
// 5. rd_en: The current state of arbitration stateARBIT,且rd_req=1 （依赖ARBIT、rd_req）


module sdram_arbit(
	input 				    clk,
	input 				    rst_n,
	
	input 				    init_end,
	input   	[3:0]		init_cmd,//SDRAM命令,组成{CS#,RAS#,CAS#,WE#}
	input   	[1:0] 		init_bank,//BANK地址,共4个BANK
	input   	[12:0]		init_addr,//SDRAM地址总线 
	
	input 	   	  			auto_ref_req,
	input 	   	  			auto_ref_end,	
	input   	[3:0]		auto_ref_cmd,//SDRAM命令,组成{CS#,RAS#,CAS#,WE#}
	input   	[1:0] 		auto_ref_bank,//BANK地址,共4个BANK
	input   	[12:0]		auto_ref_addr,//SDRAM地址总线

	
	input 	   	  			wr_req,
	input 	   	  			wr_end,	
	input   	[3:0] 		write_cmd,
	input   	[1:0] 		write_bank,
	input   	[12:0] 		write_addr,	
	input   				wr_sdram_en,//Tri-state gate judgment conditions 
	input       [15:0] 		wr_sdram_data,//如果wr_sdram_en=1,那么sdram_dq为输出端口,Will write datawr_sdram_data输出给SDRAM
	
	input 	   	  			rd_req,
	input 	   	  			rd_end,
	input   	[3:0] 		read_cmd,
	input   	[1:0] 		read_bank,
	input   	[12:0] 		read_addr,	

	
	output   	 			aref_en,
	output   	 			wr_en,
	output  		 		rd_en,
	output    		 		sdram_cke,
	
	output    		 		sdram_cs_n,
	output    		 		sdram_ras_n,
	output    		 		sdram_cas_n,
	output    		 		sdram_we_n,
	
	output reg 	[1:0] 		sdram_bank,
	output reg 	[12:0] 		sdram_addr,
	output reg 	[15:0] 		sdram_dq
);
 

//==========================================parameter===========================================================

//状态机
localparam	IDLE	= 5'b0_0001   ,   	//初始状态
            ARBIT	= 5'b0_0010   ,   	//仲裁状态
            ATREF	= 5'b0_0100   ,   	//自动刷新状态
            WRITE	= 5'b0_1000   ,   	//写状态
            READ	= 5'b1_0000   ;   	//读状态
			
//命令指令参数 
localparam	NOP		= 4'b0111     ;   	//空操作指令

//==========================================reg=================================================================
			
reg [2:0] state;
reg [2:0] next_state;
reg [3:0] sdram_cmd_reg;

//==========================================wire=================================================================


//==========================================assign=================================================================
assign sdram_cke   = 1'd1;
assign sdram_cs_n  = sdram_cmd_reg[3];
assign sdram_ras_n = sdram_cmd_reg[2];
assign sdram_cas_n = sdram_cmd_reg[1];
assign sdram_we_n  = sdram_cmd_reg[0];
//assign {sdram_cs_n, sdram_ras_n, sdram_cas_n, sdram_we_n} = sdram_cmd; 还可以这样写

assign sdram_dq = (wr_sdram_en) ? wr_sdram_data:16'bz;
//==========================================always=================================================================
[email protected](posedge clk or negedge rst_n)begin
	if(!rst_n )
		aref_en <= 1'd0;
	else if((state == ARBIT) && auto_ref_req)
		aref_en <= 1'd1;
	else if(auto_ref_end)
		aref_en <= 1'd0;
	else 
		aref_en <= aref_en;
end

[email protected](posedge clk or negedge rst_n)begin
	if(!rst_n )
		wr_en <= 1'd0;
	else if((state == ARBIT) && wr_req && (!auto_ref_req))//Priorities reflect
		wr_en <= 1'd1;
	else if(wr_end)
		wr_en <= 1'd0;
	else 
		wr_en <= wr_en;
end

[email protected](posedge clk or negedge rst_n)begin
	if(!rst_n )
		rd_en <= 1'd0;
	else if((state == ARBIT) && rd_req && (!auto_ref_req) && (!wr_req))//Priorities reflect
		rd_en <= 1'd1;
	else if(rd_end)
		rd_en <= 1'd0;
	else 
		rd_en <= rd_en;
end


//==========================================状态机=================================================================

// 第一段
[email protected](posedge clk or negedge rst_n)begin
	if(!rst_n )begin
		state <= IDLE;
	end
	else 
		state <= next_state;
end
//--状态机第二段：组合逻辑判断状态转移条件,描述状态转移规律以及输出
[email protected](*)begin
	case(state)
		IDLE:
			if(init_end)
				next_state = ARBIT;
			else 
				next_state = IDLE;
		ARBIT:  //优先级：自动刷新-写操作-读操作
			if(auto_ref_req)
				next_state = ATREF;
			else if(wr_req )
				next_state = WRITE;
			else if(rd_req)
				next_state = READ;
			else 
				next_state = ARBIT;
		ATREF: 	
			if(auto_ref_end)
				next_state = ARBIT;
			else
				next_state = ATREF;				
		WRITE:
			if(wr_end)
				next_state = ARBIT;
			else 
				next_state = WRITE;
		READ:
			if(rd_end)
				next_state = ARBIT;
			else	
				next_state = READ;

	default:next_state = IDLE;
	endcase

end

// 第三段
[email protected](*)begin
		case(state)
			IDLE:begin
				sdram_cmd_reg <= 4'd0;
			    sdram_bank 	  <= 2'd0;
			    sdram_addr	  <= 13'd0;
			end
			ATREF:begin
				sdram_cmd_reg <= auto_ref_cmd;
			    sdram_bank 	  <= auto_ref_bank;
			    sdram_addr	  <= auto_ref_addr;			
			end
			WRITE:begin
				sdram_cmd_reg <= write_cmd;
			    sdram_bank 	  <= write_bank;
			    sdram_addr	  <= write_addr;			
			end
			READ:begin
				sdram_cmd_reg <= read_cmd;
			    sdram_bank 	  <= read_bank;
			    sdram_addr	  <= read_addr;			
			end			
		default:begin
				sdram_cmd_reg <= NOP;
			    sdram_bank 	  <= 2'b11;
			    sdram_addr	  <= 13'h1fff;			
			end;
		endcase
end
endmodule