Huawei wireless device WDS configuration command

[huawei]wlan
[huawei-wlan-view]ap auth-mode mac-auth // To configure AP The authentication mode is MAC authentication , Default is MAC Address the authentication
[huawei-wlan-view]ap auth-mode sn-auth // To configure AP The authentication mode is SN authentication
[huawei-wlan-view]ap auth-mode no-auth // To configure AP The authentication mode is non authentication
[huawei-wlan-view]display ap unauthorized record // View those that have not passed the certification AP Information
[huawei-wlan-view]ap-confirm all // Confirm those that have not passed the certification AP, After the confirmation ,AP Will enter the “normal” state
[huawei-wlan-view]ap-confirm mac 1000-0000-0000
[huawei-wlan-view]ap-group name g1
[huawei-wlan-ap-group-g1]radio 0
[huawei-wlan-group-radio-g1/0]channel 20mhz 1 // Configure the working bandwidth and channel of the specified RF
[huawei-wlan-group-radio-g1/0]coverage distance 3 // Configure RF coverage distance parameters , The default RF coverage distance parameter of all RFs is 3, Unit is 100m
[huawei-wlan-group-radio-g1/0]antenna-gain 1 // Configure RF antenna gain
[huawei-wlan-group-radio-g1/0]eirp 127 // Configure RF transmission power , Default is 127dBm
[huawei-wlan-group-radio-g1/0]frequency 5g // Configure RF 0 Working in 5GHz Frequency band , Default RF 0 Working in 2.4GHz Frequency band , radio frequency 2 Working in 5GHz Frequency band
[huawei-wlan-view]radio-2g-profile name r2
[huawei-wlan-radio-2g-prof-r2]wifi-light signal-strength // To configure AP Of Wireless The flashing light indicates the signal strength
[huawei-wlan-radio-2g-prof-r2]undo ht a-mpdu disable // Can make 802.11n The frame convergence function of the Protocol
[huawei-wlan-radio-2g-prof-r2]ht a-mpdu max-length-exponent 3 // To configure 802.11n Protocol convergence frame length , default MPDU The frame length index is 3, The maximum length of the corresponding frame is 65535 byte
[huawei-wlan-radio-2g-prof-r2]beamforming enable // Enable beamforming
[huawei-wlan-view]wired-port-profile name w1 // Create and enter AP Wired port template view
[huawei-wlan-wired-port-w1]mode root // To configure AP The working mode of the wired port is root Pattern , root AP and AC The connected wired port must work in root Pattern
[huawei-wlan-wired-port-w1]mode endpoint // To configure AP The working mode of the wired port is endpoint Pattern , You can directly connect to the host or deploy the layer-2 network
[huawei-wlan-wired-port-w1]vlan pvid 10 // To configure AP It's wired pvid
[huawei-wlan-wired-port-w1]vlan tagged 10 // To configure AP Wired port VLAN, default AP All wired ports are connected VLAN, among VLAN1 With untagged Join in AP Wired port , other VLAN With tagged Join in AP Wired port
[huawei-wlan-wired-port-w1]vlan untagged 10
[huawei-wlan-wired-port-w1]user-isolate all // Can make AP User isolation function of wired port
[huawei-wlan-wired-port-w1]user-isolate l2
[huawei-wlan-view]wds-whitelist-profile name w1 // Create and enter WDS Whitelist template view
[huawei-wlan-wds-whitelist-w1]peer-ap mac 1000-0000-0000 // stay WDS Add allowed neighbors to the white list template AP The physical MAC Address
[huawei-wlan-view]wds-profile name w1 // Create and enter WDS Templates
[huawei-wlan-wds-prof-w1]wds-name w1 // To configure WDS Bridge identification of the template ,WDS Links are established between adjacent nodes through bridge identification , default WDS The bridge identification of the template is “HUAWEI-WLAN-WDS”
[huawei-wlan-wds-prof-w1]wds-mode root // To configure WDS Bridge mode of template
[huawei-wlan-wds-prof-w1]wds-mode middle
[huawei-wlan-wds-prof-w1]wds-mode leaf
[huawei-wlan-wds-prof-w1]security-profile s1 // stay WDS The security template is referenced on the template , default WDS The template references the name “default-wds” Security template for
[huawei-wlan-wds-prof-w1]vlan tagged 10 // stay WDS The template is marked with Tagged Form add a VLAN
[huawei-wlan-wds-prof-w1]beacon-2g-rate 1 // To configure 2.4GHz RF type Beacon Transmission rate of frames , The default is 1Mbps
[huawei-wlan-wds-prof-w1]beacon-5g-rate 6 // To configure 5GHz RF type Beacon Transmission rate of frames , Default is 6Mbps
[huawei-wlan-wds-prof-w1]mu-mimo enable // Turn on MU-MIMO function
[huawei-wlan-wds-prof-w1]dhcp trust port // stay WDS Configure on the template DHCP Port Trust
[huawei-wlan-wds-prof-w1]priority-map trust dot1p // To configure WDS Air interface priority mapping trust type , The default is dscp
[huawei-wlan-wds-prof-w1]priority-map trust dscp
[huawei-wlan-wds-prof-w1]priority-map dscp 1 dot11e 0 // To configure WDS Empty mouth DSCP To 802.11e Priority mapping relationship
[huawei-wlan-view]ap-group name g1
[huawei-wlan-ap-group-g1]wds-profile w1 radio all // stay AP Group references WDS Templates
[huawei-wlan-ap-group-g1]radio 0
[huawei-wlan-group-radio-g1/0]wds-profile w1 // To configure AP RF reference WDS Templates
[huawei]display references wds-profile name w1 // View specified WDS Reference information of the template
[huawei]display wds-profile all // see WDS Template information
[huawei]display references wds-whitelist-profile name w1 // View specified WDS Reference information of whitelist template
[huawei]display wds-whitelist-profile all // see WDS White list template information
[huawei]display wds vap all // View all WDS type VAP Information about
[huawei]display wds vap ap-group g1 // see WDS type VAP Information about
[huawei]display wlan wds link all // see WDS Link related information
[huawei-wlan-view]vap-profile name v1 // establish VAP Templates , And enter the template view
[huawei-wlan-vap-prof-v1]temporary-management enable // To configure VAP For offline management VAP Align with the antenna VAP
[huawei-wlan-view]ap-system-profile name s1 // Create and enter AP System template view
[huawei-wlan-ap-system-prof-s1]temporary-management enable // Can make AP Offline Management VAP Function and antenna alignment VAP function