Nuc980 started successfully

[18:30:06.684]
[18:30:06.689] NUC980 IBR 20180813
[18:30:06.689] Boot from SPI-NOR
[18:30:06.689] DDR-OK
[18:30:06.767] finish SPI dow 頾 ad
[18:30:06.769]
[18:30:06.769]
[18:30:06.769] U-Boot 2016.11 (Jun 28 2022 - 18:22:13 +0800)
[18:30:06.779]
[18:30:06.779] CPU: NUC980
[18:30:06.779] Board: NUC980
[18:30:06.779] DRAM: 64 MiB
[18:30:07.037] NAND: 4096 MiB
[18:30:07.039] SF: Detected MX25L25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
[18:30:07.737] *** Warning - bad CRC, using default environment
[18:30:07.749]
[18:30:07.755] In: serial
[18:30:07.760] Out: serial
[18:30:07.760] Err: serial
[18:30:07.777] Net: Net Initialization Skipped
[18:30:07.779] No ethernet found.
[18:30:07.779] =>
sf probe
[18:30:12.602] SF: Detected MX25L25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
[18:30:12.612] =>
sf probe 0 50000000
[18:30:19.907] SF: Detected MX25L25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
[18:30:19.917] =>
sf read 0x7fc0 0x200000 0x800000
[18:31:01.602] device 0 offset 0x200000, size 0x800000
[18:31:03.533] SF: 8388608 bytes @ 0x200000 Read: OK
[18:31:03.544] =>
bootm 0x7fc0
[18:31:17.739] ## Booting kernel from Legacy Image at 00007fc0 …
[18:31:17.749] Image Name: Linux-4.4.115+
[18:31:17.749] Image Type: ARM Linux Kernel Image (uncompressed)
[18:31:17.749] Data Size: 6491248 Bytes = 6.2 MiB
[18:31:17.758] Load Address: 00008000
[18:31:17.758] Entry Point: 00008000
[18:31:17.758] Verifying Checksum …
OK
[18:31:21.408] XIP Kernel Image … OK
[18:31:21.408]
[18:31:21.408] Starting kernel …
[18:31:21.408]
[18:31:21.408] SF: Detected MX25L25635F with page size 256 Bytes, erase size 64 KiB, total 32 MiB
[18:31:21.419] SF: Device
Booting Linux on physical CPU 0x0
[18:31:22.559] Linux version 4.4.115+ ([email protected]) (gcc version 4.8.4 (GCC) ) #215 PREEMPT Wed Mar 6 09:43:03 CST 2019
[18:31:22.559] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[18:31:22.568] CPU: VIVT data cache, VIVT instruction cache
[18:31:22.568] Machine: NUC980
[18:31:22.579] Memory policy: Data cache writeback
[18:31:22.579] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[18:31:22.589] Kernel command line: root=/dev/ram0 console=ttyS0,115200n8 rdinit=/sbin/init mem=64M
[18:31:22.589] PID hash table entries: 256 (order: -2, 1024 bytes)
[18:31:22.599] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[18:31:22.599] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[18:31:22.609] Memory: 55828K/65536K available (3306K kernel code, 269K rwdata, 1068K rodata, 4200K init, 209K bss, 9708K reserved, 0K cma-reserved)
[18:31:22.618] Virtual kernel memory layout:
[18:31:22.628] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[18:31:22.628] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[18:31:22.628] vmalloc : 0xc4800000 - 0xff800000 ( 944 MB)
[18:31:22.638] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[18:31:22.638] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[18:31:22.649] .text : 0xc0008000 - 0xc044df4c (4376 kB)
[18:31:22.649] .init : 0xc044e000 - 0xc0868000 (4200 kB)
[18:31:22.649] .data : 0xc0868000 - 0xc08ab6c0 ( 270 kB)
[18:31:22.659] .bss : 0xc08ab6c0 - 0xc08dfe84 ( 210 kB)
[18:31:22.659] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[18:31:22.670] Preemptible hierarchical RCU implementation.
[18:31:22.670] Build-time adjustment of leaf fanout to 32.
[18:31:22.678] NR_IRQS:545
[18:31:22.678] clocksource: nuc980-timer5: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 62215505635 ns
[18:31:22.678] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns
[18:31:22.689] Console: colour dummy device 80x30
[18:31:22.689] console [ttyS0] enabled
[18:31:22.699] Calibrating delay loop… 148.88 BogoMIPS (lpj=744448)
[18:31:22.761] pid_max: default: 32768 minimum: 301
[18:31:22.769] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[18:31:22.769] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[18:31:22.779] CPU: Testing write buffer coherency: ok
[18:31:22.788] Setting up static identity map for 0x8400 - 0x843c
[18:31:22.793] devtmpfs: initialized
[18:31:22.816] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[18:31:22.829] futex hash table entries: 256 (order: -1, 3072 bytes)
[18:31:22.829] pinctrl core: initialized pinctrl subsystem
[18:31:22.836] NET: Registered protocol family 16
[18:31:22.838] DMA: preallocated 256 KiB pool for atomic coherent allocations
[18:31:22.956] SCSI subsystem initialized
[18:31:22.967] usbcore: registered new interface driver usbfs
[18:31:22.976] usbcore: registered new interface driver hub
[18:31:22.978] usbcore: registered new device driver usb
[18:31:22.989] Advanced Linux Sound Architecture Driver Initialized.
[18:31:22.994] clocksource: Switched to clocksource nuc980-timer5
[18:31:23.088] NET: Registered protocol family 2
[18:31:23.099] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[18:31:23.106] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[18:31:23.108] TCP: Hash tables configured (established 1024 bind 1024)
[18:31:23.118] UDP hash table entries: 256 (order: 0, 4096 bytes)
[18:31:23.118] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[18:31:23.128] NET: Registered protocol family 1
[18:31:24.606] NetWinder Floating Point Emulator V0.97 (double precision)
[18:31:24.737] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[18:31:24.748] io scheduler noop registered (default)
[18:31:24.750] nuc980_gpio_probe - pdev = nuc980-gpio
[18:31:24.765] nuc980_dma_probe - pdev = nuc980-dma
[18:31:24.785] nuc980-dma nuc980-dma: NUC980 DMA ready
[18:31:25.378] nuc980-uart.0: ttyS0 at I/O 0x0 (irq = 36, base_baud = 750000) is a NUC980
[18:31:25.385] nuc980-uart.1: ttyS1 at I/O 0x0 (irq = 37, base_baud = 9375000) is a NUC980
[18:31:25.468] brd: module loaded
[18:31:25.483] RX nuc980_qspi0_probe: dma0chan0 module removed
[18:31:25.488] TX nuc980_qspi0_probe: dma0chan1 module removed
[18:31:25.496] RX nuc980_spi0_probe: dma0chan2 module removed
[18:31:25.499] TX nuc980_spi0_probe: dma0chan3 module removed
[18:31:25.509] m25p80 spi1.0: unrecognized JEDEC id bytes: ff, ff, ff
[18:31:25.518] m25p80: probe of spi1.0 failed with error -2
[18:31:25.534] libphy: nuc980_rmii0: probed
[18:31:25.547] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[18:31:25.548] nuc980-ehci nuc980-ehci: Nuvoton NUC980 EHCI Host Controller
[18:31:25.559] nuc980-ehci nuc980-ehci: new USB bus registered, assigned bus number 1
[18:31:25.569] nuc980-ehci nuc980-ehci: irq 23, io mem 0xb0015000
[18:31:25.587] nuc980-ehci nuc980-ehci: USB 2.0 started, EHCI 0.95
[18:31:25.597] hub 1-0:1.0: USB hub found
[18:31:25.599] hub 1-0:1.0: 2 ports detected
[18:31:25.608] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[18:31:25.609] usb_hcd_nuc980_probe, id = 0, name: nuc980-ohci.0
[18:31:25.619] nuc980-ohci nuc980-ohci.0: Nuvoton NUC980 OHCI Host Controller
[18:31:25.628] nuc980-ohci nuc980-ohci.0: new USB bus registered, assigned bus number 2
[18:31:25.628] nuc980-ohci nuc980-ohci.0: irq 24, io mem 0xb0017000
[18:31:25.694] hub 2-0:1.0: USB hub found
[18:31:25.699] hub 2-0:1.0: 8 ports detected
[18:31:25.706] usb_hcd_nuc980_probe, id = 1, name: nuc980-ohci.1
[18:31:25.709] usb_hcd_nuc980_probe, id = 2, name: nuc980-ohci.2
[18:31:25.718] usb_hcd_nuc980_probe, id = 3, name: nuc980-ohci.3
[18:31:25.718] usb_hcd_nuc980_probe, id = 4, name: nuc980-ohci.4
[18:31:25.728] usb_hcd_nuc980_probe, id = 5, name: nuc980-ohci.5
[18:31:25.728] usb_hcd_nuc980_probe, id = 6, name: nuc980-ohci.6
[18:31:25.739] usbcore: registered new interface driver usb-storage
[18:31:25.747] nuc980-i2c0 nuc980-i2c0: i2c-0: nuc980 I2C adapter
[18:31:25.749] nuc980-i2c2 nuc980-i2c2: i2c-2: nuc980 I2C adapter
[18:31:25.758] nuc980_sd_probe - pdev = nuc980-sdh
[18:31:25.807] usbcore: registered new interface driver usbhid
[18:31:25.808] usbhid: USB HID core driver
[18:31:25.915] usb 1-2: new high-speed USB device number 2 using nuc980-ehci
[18:31:26.073] hub 1-2:1.0: USB hub found
[18:31:26.079] hub 1-2:1.0: 4 ports detected
[18:31:26.285] random: nonblocking pool is initialized
[18:32:05.827] mt29f spi0.0: WAIT timedout!!!
[18:32:45.834] mt29f spi0.0: wait timedout!
[18:32:45.838] nand: No NAND device found
[18:32:45.841] nuc980-nadc: nuc980 Normal ADC adapter