当前位置：网站首页>基于FPGA的MCP4725驱动程序
基于FPGA的MCP4725驱动程序
2020-11-10 10:46:00 【osc_bmrl02u3】
基于FPGA的MCP4725驱动程序
- 芯片资料
MCP4725是低功耗、高精度、单通道的12位缓冲电压输出数模转换器（Digital-to-Analog Convertor，DAC)，具有非易失性存储器（EEPROM)。用户可以使用I2C接口命令将DAC输入和配置数据烧写到非易失性存储器（EEPROM)。非易失性存储器功能使得DAC器件在断电期间仍能保持DAC输入代码，且DAC输出在上电后立即可用。
图1.MCP4725功能框图
MCP4725具有外部A0地址位选择引脚。此A0引脚可连接用户应用电路板的VDD或VSS。MCP4725具有2线型IIC兼容串行接口，可用于标准（100 kHz）、快速（400 kHz）或高速（3.4 MHz）模式。
Vout：模拟输出电压；
Vss：参考地；
VDD：电源电压；3.7~5.5V
SDA：IIC串行数据；
SCL：IIC串行时钟输入
A0：地址位选择引脚；该引脚可连接到VSS或VDD ，或由数字逻辑电平有效驱动。该引脚的逻辑状态决定了I2 C地址位的A0位。
2. 输出电压计算
例如当我们输入0x400，即十进制数1024，电源电压接入为5V，那么输出电压Vout=5*1024/4096=1.25V。
3. 工作原理
当器件连接到I2C总线时，器件作为从器件工作。使用I2C接口命令，主器件可以读/写DAC输入寄存器或EEPROM。MCP4725器件地址包含4个固定位(1100 =器件代码)和3个地址位(A2、A1和A0)。A2和A1位是在出厂前硬连线的，而A0位由A0引脚的逻辑状态决定。A0引脚可连接到VDD或VSS，或由数字逻辑电平有效驱动。写命令用于将配置位和DAC输入代码装载到DAC寄存器，或写入器件的EEPROM。通过使用3个写命令类型位(C2、C1和C0)定义写命令类型。
当C2=0,C1=0 时，为快速模式，此命令用于更改DAC寄存器，EEPROM不受影响；当C2=0,C1=1,C0=0 时，为写DAC寄存器模式，即将配置位和数据代码装载到DAC寄存器；当C2=0,C1=1,C0=1 时，为写DAC寄存器和更新EEPROM模式,将配置位和数据代码装载到DAC寄存器并且写入EEPROM中。本次主要使用写DAC寄存器模式和写DAC寄存器和更新EEPROM模式，如下图所示。
第一个字节为器件寻址，A2和A1已经被厂家设置为0，A0由自己控制(默认为0，即接地)，因此第一个字节为0x60；第二个字节为写数据地址，PD0和PD1都为0时为正常模式，因此第二个字节为0x60；第三个字节和第四个字节的高4位组成12位数据输入，由我们自己定义输入。
4. IIC串行通信
MCP4725器件使用2线IIC串行接口，该接口可在标准、快速或高速模式下工作。在总线上发送数据的器件定义为发送器，而接收数据的器件定义为接收器。总线必须由主器件控制，主器件产生串行时(SCL)信号、控制总线访问权并产生启动条件和停止条件。MCP4725器件作为从器件工作。主器件和从器件都可以作为发送器或接收器工作，但是由主器件决定激活哪种模式。通信由主器件（单片机）发起，它发送启动位，随后是从地址字节。发送的第一个字节始终为从地址字节，它包含器件代码、地址位和R/W位。MCP4725器件的器件代码为1100。当器件接收到读命令(R/W = 1)时，发送DAC输入寄存器和EEPROM的内容。下图给出了IIC通信时序要求。
在本次设计中，SCL时钟输入频率选择为250KHz，FPGA工作时钟为50MHz，上电等待20ms后开始IIC数据写入。采用模块化设计，分为IIC驱动设计，MCP4725初始化设计，顶层模块。
5. 代码模块
5.1 IIC驱动模块
module i2c_dri
#(// slave address（器件地址）
parameter SLAVE_ADDR = 7'b1100000 ,
parameter CLK_FREQ = 26'd50_000_000, // 时钟频率(CLK_FREQ)
parameter I2C_FREQ = 18'd250_000 // I2C的SCL时钟频率
)(
//global clock
input clk , // 时钟
input rst_n , // 复位信号
//i2c interface
input i2c_exec , // I2C触发执行信号
input bit_ctrl , // 字地址位控制(16b/8b)
input i2c_rh_wl , // I2C读写控制信号
input [15:0] i2c_addr , // I2C器件内地址
input [15:0] i2c_data_w , // I2C要写的数据
output reg [ 7:0] i2c_data_r , // I2C读出的数据
output reg i2c_done , // I2C一次操作完成
output reg scl , // I2C的SCL时钟信号
inout sda , // I2C的SDA信号
//user interface
output reg dri_clk // 驱动I2C操作的驱动时钟
);
//localparam define
localparam st_idle = 8'b0000_0001; // 空闲状态
localparam st_sladdr = 8'b0000_0010; // 发送器件地址(slave address)
localparam st_addr16 = 8'b0000_0100; // 发送16位字地址
localparam st_addr8 = 8'b0000_1000; // 发送8位字地址
localparam st_data_wr = 8'b0001_0000; // 写数据(8 bit)
localparam st_addr_rd = 8'b0010_0000; // 发送器件地址读
localparam st_data_rd = 8'b0100_0000; // 读数据(8 bit)
localparam st_stop = 8'b1000_0000; // 结束I2C操作
//reg define
reg sda_dir ; // I2C数据(SDA)方向控制
reg sda_out ; // SDA输出信号
reg st_done ; // 状态结束
reg wr_flag ; // 写标志
reg [ 6:0] cnt ; // 计数
reg [ 7:0] cur_state ; // 状态机当前状态
reg [ 7:0] next_state ; // 状态机下一状态
reg [15:0] addr_t ; // 地址
reg [ 7:0] data_r ; // 读取的数据
reg [15:0] data_wr_t ; // I2C需写的数据的临时寄存
reg [ 9:0] clk_cnt ; // 分频时钟计数
//wire define
wire sda_in ; // SDA输入信号
wire [8:0] clk_divide ; // 模块驱动时钟的分频系数
//SDA控制
assign sda = sda_dir ? sda_out : 1'bz; // SDA数据输出或高阻
assign sda_in = sda ; // SDA数据输入
assign clk_divide = (CLK_FREQ/I2C_FREQ) >> 3; // 模块驱动时钟的分频系数
//生成I2C的SCL的四倍频率的驱动时钟用于驱动i2c的操作
always @(posedge clk or negedge rst_n) begin
if(!rst_n) begin
dri_clk <= 1'b1;
clk_cnt <= 10'd0;
end
else if(clk_cnt == clk_divide - 1'd1) begin
clk_cnt <= 10'd0;
dri_clk <= ~dri_clk;
end
else
clk_cnt <= clk_cnt + 1'b1;
end
//(三段式状态机)同步时序描述状态转移
always @(posedge dri_clk or negedge rst_n) begin
if(!rst_n)
cur_state <= st_idle;
else
cur_state <= next_state;
end
//组合逻辑判断状态转移条件
always @( * ) begin
// next_state = st_idle;
case(cur_state)
st_idle: begin // 空闲状态
if(i2c_exec) begin
next_state = st_sladdr;
end
else
next_state = st_idle;
end
st_sladdr: begin
if(st_done) begin
if(bit_ctrl) // 判断是16位还是8位字地址
next_state = st_addr16;
else
next_state = st_addr8 ;
end
else
next_state = st_sladdr;
end
st_addr16: begin // 写16位字地址
if(st_done) begin
next_state = st_addr8;
end
else begin
next_state = st_addr16;
end
end
st_addr8: begin // 8位字地址
if(st_done) begin
if(wr_flag==1'b0) // 读写判断
next_state = st_data_wr;
else
next_state = st_addr_rd;
end
else begin
next_state = st_addr8;
end
end
st_data_wr: begin // 写数据(8 bit)
if(st_done)
next_state = st_stop;
else
next_state = st_data_wr;
end
st_addr_rd: begin // 写地址以进行读数据
if(st_done) begin
next_state = st_data_rd;
end
else begin
next_state = st_addr_rd;
end
end
st_data_rd: begin // 读取数据(8 bit)
if(st_done)
next_state = st_stop;
else
next_state = st_data_rd;
end
st_stop: begin // 结束I2C操作
if(st_done)
next_state = st_idle;
else
next_state = st_stop ;
end
default: next_state= st_idle;
endcase
end
//时序电路描述状态输出
always @(posedge dri_clk or negedge rst_n) begin
//复位初始化
if(!rst_n) begin
scl <= 1'b1;
sda_out <= 1'b1;
sda_dir <= 1'b1;
i2c_done <= 1'b0;
cnt <= 1'b0;
st_done <= 1'b0;
data_r <= 1'b0;
i2c_data_r <= 1'b0;
wr_flag <= 1'b0;
addr_t <= 1'b0;
data_wr_t <= 1'b0;
end
else begin
st_done <= 1'b0 ;
cnt <= cnt +1'b1 ;
case(cur_state)
st_idle: begin // 空闲状态
scl <= 1'b1;
sda_out <= 1'b1;
sda_dir <= 1'b1;
i2c_done<= 1'b0;
cnt <= 7'b0;
if(i2c_exec) begin
wr_flag <= i2c_rh_wl ;
addr_t <= i2c_addr ;
data_wr_t <= i2c_data_w;
end
end
st_sladdr: begin // 写地址(器件地址和字地址)
case(cnt)
7'd1 : sda_out <= 1'b0; // 开始I2C
7'd3 : scl <= 1'b0;
7'd4 : sda_out <= SLAVE_ADDR[6]; // 传送器件地址
7'd5 : scl <= 1'b1;
7'd7 : scl <= 1'b0;
7'd8 : sda_out <= SLAVE_ADDR[5];
7'd9 : scl <= 1'b1;
7'd11: scl <= 1'b0;
7'd12: sda_out <= SLAVE_ADDR[4];
7'd13: scl <= 1'b1;
7'd15: scl <= 1'b0;
7'd16: sda_out <= SLAVE_ADDR[3];
7'd17: scl <= 1'b1;
7'd19: scl <= 1'b0;
7'd20: sda_out <= SLAVE_ADDR[2];
7'd21: scl <= 1'b1;
7'd23: scl <= 1'b0;
7'd24: sda_out <= SLAVE_ADDR[1];
7'd25: scl <= 1'b1;
7'd27: scl <= 1'b0;
7'd28: sda_out <= SLAVE_ADDR[0];
7'd29: scl <= 1'b1;
7'd31: scl <= 1'b0;
7'd32: sda_out <= 1'b0; // 0:写
7'd33: scl <= 1'b1;
7'd35: scl <= 1'b0;
7'd36: begin
sda_dir <= 1'b0; // 从机应答
sda_out <= 1'b1;
end
7'd37: scl <= 1'b1;
7'd38: st_done <= 1'b1;
7'd39: begin
scl <= 1'b0;
cnt <= 1'b0;
end
default : ;
endcase
end
st_addr16: begin
case(cnt)
7'd0 : begin
sda_dir <= 1'b1 ;
sda_out <= addr_t[15]; // 传送字地址
end
7'd1 : scl <= 1'b1;
7'd3 : scl <= 1'b0;
7'd4 : sda_out <= addr_t[14];
7'd5 : scl <= 1'b1;
7'd7 : scl <= 1'b0;
7'd8 : sda_out <= addr_t[13];
7'd9 : scl <= 1'b1;
7'd11: scl <= 1'b0;
7'd12: sda_out <= addr_t[12];
7'd13: scl <= 1'b1;
7'd15: scl <= 1'b0;
7'd16: sda_out <= addr_t[11];
7'd17: scl <= 1'b1;
7'd19: scl <= 1'b0;
7'd20: sda_out <= addr_t[10];
7'd21: scl <= 1'b1;
7'd23: scl <= 1'b0;
7'd24: sda_out <= addr_t[9];
7'd25: scl <= 1'b1;
7'd27: scl <= 1'b0;
7'd28: sda_out <= addr_t[8];
7'd29: scl <= 1'b1;
7'd31: scl <= 1'b0;
7'd32: begin
sda_dir <= 1'b0; // 从机应答
sda_out <= 1'b1;
end
7'd33: scl <= 1'b1;
7'd34: st_done <= 1'b1;
7'd35: begin
scl <= 1'b0;
cnt <= 1'b0;
end
default : ;
endcase
end
st_addr8: begin
case(cnt)
7'd0: begin
sda_dir <= 1'b1 ;
sda_out <= addr_t[7]; // 字地址
end
7'd1 : scl <= 1'b1;
7'd3 : scl <= 1'b0;
7'd4 : sda_out <= addr_t[6];
7'd5 : scl <= 1'b1;
7'd7 : scl <= 1'b0;
7'd8 : sda_out <= addr_t[5];
7'd9 : scl <= 1'b1;
7'd11: scl <= 1'b0;
7'd12: sda_out <= addr_t[4];
7'd13: scl <= 1'b1;
7'd15: scl <= 1'b0;
7'd16: sda_out <= addr_t[3];
7'd17: scl <= 1'b1;
7'd19: scl <= 1'b0;
7'd20: sda_out <= addr_t[2];
7'd21: scl <= 1'b1;
7'd23: scl <= 1'b0;
7'd24: sda_out <= addr_t[1];
7'd25: scl <= 1'b1;
7'd27: scl <= 1'b0;
7'd28: sda_out <= addr_t[0];
7'd29: scl <= 1'b1;
7'd31: scl <= 1'b0;
7'd32: begin
sda_dir <= 1'b0; // 从机应答
sda_out <= 1'b1;
end
7'd33: scl <= 1'b1;
7'd34: st_done <= 1'b1;
7'd35: begin
scl <= 1'b0;
cnt <= 1'b0;
end
default : ;
endcase
end
st_data_wr: begin // 写数据(12 bit)
case(cnt)
7'd0: begin
sda_out <= data_wr_t[15]; // I2C写2次8位数据
sda_dir <= 1'b1;
end
7'd1 : scl <= 1'b1;
7'd3 : scl <= 1'b0;
7'd4 : sda_out <= data_wr_t[14];
7'd5 : scl <= 1'b1;
7'd7 : scl <= 1'b0;
7'd8 : sda_out <= data_wr_t[13];
7'd9 : scl <= 1'b1;
7'd11: scl <= 1'b0;
7'd12: sda_out <= data_wr_t[12];
7'd13: scl <= 1'b1;
7'd15: scl <= 1'b0;
7'd16: sda_out <= data_wr_t[11];
7'd17: scl <= 1'b1;
7'd19: scl <= 1'b0;
7'd20: sda_out <= data_wr_t[10];
7'd21: scl <= 1'b1;
7'd23: scl <= 1'b0;
7'd24: sda_out <= data_wr_t[9];
7'd25: scl <= 1'b1;
7'd27: scl <= 1'b0;
7'd28: sda_out <= data_wr_t[8];
7'd29: scl <= 1'b1;
7'd31: scl <= 1'b0;
7'd32: begin
sda_dir <= 1'b0; // 从机应答
sda_out <= 1'b1;
end
7'd33: scl <= 1'b1;
7'd35: scl <= 1'b0;
7'd36: sda_out <= data_wr_t[7];
7'd37: scl <= 1'b1;
7'd39: scl <= 1'b0;
7'd40: sda_out <= data_wr_t[6];
7'd41: scl <= 1'b1;
7'd43: scl <= 1'b0;
7'd44: sda_out <= data_wr_t[5];
7'd45: scl <= 1'b1;
7'd47: scl <= 1'b0;
7'd48: sda_out <= data_wr_t[4];
7'd49: scl <= 1'b1;
7'd51: scl <= 1'b0;
7'd52: sda_out <= data_wr_t[3];
7'd53: scl <= 1'b1;
7'd55: scl <= 1'b0;
7'd56: sda_out <= data_wr_t[2];
7'd57: scl <= 1'b1;
7'd59: scl <= 1'b0;
7'd60: sda_out <= data_wr_t[1];
7'd61: scl <= 1'b1;
7'd63: scl <= 1'b0;
7'd64: sda_out <= data_wr_t[0];
7'd65: scl <= 1'b1;
7'd67: scl <= 1'b0;
7'd68: begin
sda_dir <= 1'b0; // 从机应答
sda_out <= 1'b1;
end
7'd69: scl <= 1'b1;
7'd70: st_done <= 1'b1;
7'd71: begin
scl <= 1'b0;
cnt <= 1'b0;
end
default : ;
endcase
end
st_addr_rd: begin // 写地址以进行读数据
case(cnt)
7'd0 : begin
sda_dir <= 1'b1;
sda_out <= 1'b1;
end
7'd1 : scl <= 1'b1;
7'd2 : sda_out <= 1'b0; // 重新开始
7'd3 : scl <= 1'b0;
7'd4 : sda_out <= SLAVE_ADDR[6]; // 传送器件地址
7'd5 : scl <= 1'b1;
7'd7 : scl <= 1'b0;
7'd8 : sda_out <= SLAVE_ADDR[5];
7'd9 : scl <= 1'b1;
7'd11: scl <= 1'b0;
7'd12: sda_out <= SLAVE_ADDR[4];
7'd13: scl <= 1'b1;
7'd15: scl <= 1'b0;
7'd16: sda_out <= SLAVE_ADDR[3];
7'd17: scl <= 1'b1;
7'd19: scl <= 1'b0;
7'd20: sda_out <= SLAVE_ADDR[2];
7'd21: scl <= 1'b1;
7'd23: scl <= 1'b0;
7'd24: sda_out <= SLAVE_ADDR[1];
7'd25: scl <= 1'b1;
7'd27: scl <= 1'b0;
7'd28: sda_out <= SLAVE_ADDR[0];
7'd29: scl <= 1'b1;
7'd31: scl <= 1'b0;
7'd32: sda_out <= 1'b1; // 1:读
7'd33: scl <= 1'b1;
7'd35: scl <= 1'b0;
7'd36: begin
sda_dir <= 1'b0; // 从机应答
sda_out <= 1'b1;
end
7'd37: scl <= 1'b1;
7'd38: st_done <= 1'b1;
7'd39: begin
scl <= 1'b0;
cnt <= 1'b0;
end
default : ;
endcase
end
st_data_rd: begin // 读取数据(8 bit)
case(cnt)
7'd0: sda_dir <= 1'b0;
7'd1: begin
data_r[7] <= sda_in;
scl <= 1'b1;
end
7'd3: scl <= 1'b0;
7'd5: begin
data_r[6] <= sda_in ;
scl <= 1'b1 ;
end
7'd7: scl <= 1'b0;
7'd9: begin
data_r[5] <= sda_in;
scl <= 1'b1 ;
end
7'd11: scl <= 1'b0;
7'd13: begin
data_r[4] <= sda_in;
scl <= 1'b1 ;
end
7'd15: scl <= 1'b0;
7'd17: begin
data_r[3] <= sda_in;
scl <= 1'b1 ;
end
7'd19: scl <= 1'b0;
7'd21: begin
data_r[2] <= sda_in;
scl <= 1'b1 ;
end
7'd23: scl <= 1'b0;
7'd25: begin
data_r[1] <= sda_in;
scl <= 1'b1 ;
end
7'd27: scl <= 1'b0;
7'd29: begin
data_r[0] <= sda_in;
scl <= 1'b1 ;
end
7'd31: scl <= 1'b0;
7'd32: begin
sda_dir <= 1'b1; // 非应答
sda_out <= 1'b1;
end
7'd33: scl <= 1'b1;
7'd34: st_done <= 1'b1;
7'd35: begin
scl <= 1'b0;
cnt <= 1'b0;
i2c_data_r <= data_r;
end
default : ;
endcase
end
st_stop: begin // 结束I2C操作
case(cnt)
7'd0: begin
sda_dir <= 1'b1; // 结束I2C
sda_out <= 1'b0;
end
7'd1 : scl <= 1'b1;
7'd3 : sda_out <= 1'b1;
7'd15: st_done <= 1'b1;
7'd16: begin
cnt <= 1'b0;
i2c_done <= 1'b1; // 向上层模块传递I2C结束信号
end
default : ;
endcase
end
endcase
end
end
endmodule
5.2 MCP4725初始化模块
module MCP4725_init(
input clk , //时钟信号
input rst_n , //复位信号，低电平有效
input i2c_done , //I2C寄存器配置完成信号
output reg i2c_exec , //I2C触发执行信号
output reg [23:0] i2c_data //I2C要配置的地址与数据(高16位地址,低8位数据)
);
//reg define
reg [14:0] start_init_cnt; //等待延时计数器
//scl配置成250khz,输入的clk为1Mhz,周期为1us,20000*1us = 20ms
//上电到开始配置IIC至少等待20ms
always @(posedge clk or negedge rst_n) begin
if(!rst_n)
start_init_cnt <= 15'd0;
else if(start_init_cnt < 15'd20000)
start_init_cnt <= start_init_cnt + 1'b1;
end
//i2c触发执行信号
always @(posedge clk or negedge rst_n) begin
if(!rst_n)
i2c_exec <= 1'b0;
else if(start_init_cnt == 15'd19999)
i2c_exec <= 1'b1;
else
i2c_exec <= 1'b0;
end
//配置寄存器地址与数据
always @(posedge clk or negedge rst_n) begin
if(!rst_n)
i2c_data <= 16'd0;
else
i2c_data <= {
8'h60,8'h40,8'h00} ;//第一个字节为模式控制（60:同步更新到EEPROM;40:只更新DAC寄存器），后面两个字节为输入数据，取高12位
end
endmodule
5.3 顶层模块
module MCP4725_CTRL(
input clk,
input rst_n,
output scl,
inout sda
);
wire i2c_exec ; //I2C触发执行信号
wire [23:0] i2c_data ; //I2C要配置的地址与数据(高8位地址,低16位数据)
wire i2c_done ; //I2C寄存器配置完成信号
wire i2c_dri_clk ; //I2C操作时钟
parameter SLAVE_ADDR = 7'h60 ; //MCP4725的器件地址7'h60
parameter BIT_CTRL = 1'b0 ; //字节地址为8位 0:8位 1:16位
parameter CLK_FREQ = 26'd50_000_000; //时钟频率 50MHz
parameter I2C_FREQ = 18'd250_000 ; //I2C的SCL时钟频率,250KHz
i2c_dri
#(
.SLAVE_ADDR (SLAVE_ADDR), //参数传递
.CLK_FREQ (CLK_FREQ ),
.I2C_FREQ (I2C_FREQ )
)
u_i2c_dri(
.clk (clk ),
.rst_n (rst_n ),
.i2c_exec (i2c_exec ),
.bit_ctrl (BIT_CTRL ),
.i2c_rh_wl (1'b0), //固定为0，只用到了IIC驱动的写操作
.i2c_addr (i2c_data[23:16]),
.i2c_data_w (i2c_data[15:0]),
.i2c_data_r (),
.i2c_done (i2c_done ),
.scl (scl ),
.sda (sda ),
.dri_clk (i2c_dri_clk) //I2C操作时钟
);
MCP4725_init u_MCP4725_init(
.clk (i2c_dri_clk), //时钟信号
.rst_n (rst_n), //复位信号，低电平有效
.i2c_done(i2c_done), //I2C寄存器配置完成信号
.i2c_exec(i2c_exec), //I2C触发执行信号
.i2c_data(i2c_data) //I2C要配置的地址与数据(高8位地址,低16位数据)
);
endmodule
PS：IIC驱动程序是我在以前写的IIC单字节读写程序的基础上修改而来，从而实现两个字节的写入(这里可以再增加实现多个字节的写入，但要注意cnt的位宽)。MCP4725初始化程序中最后的 i2c_data <= {8’h60,8’h40,8’h00} ; 这一行大家可以根据自己的实际需求做更改，详细更改的内容自行参考芯片的数据手册。
6.验证
将工程编译好后的sof文件下载到EP4CE6F17C8器件中，连接好MCP4725各个引脚，电源接5V，输入的数据为1024，为4096的四分之一，因此输出电压应该为1.25V，利用万用表测量数据为1.25V，将模块断电再重新上电，再次测量也为1.25V，证明数据成功写入EEPROM中，验证成功。
版权声明
本文为[osc_bmrl02u3]所创，转载请带上原文链接，感谢
https://my.oschina.net/u/4398140/blog/4710747
边栏推荐
- Factory approach model
- Only options request is sent, no post solution is sent
- 工厂方法模式
- 浅谈字节最新开源联邦机器学习平台Fedlearner
- 网络安全工程师演示：原来***是这样控制你的服务器的！（下）
- Farfetch、阿里巴巴集团和历峰集团结成全球合作伙伴关系，将加速奢侈品行业数字化进程
- JS solves the problem of automatic pagination in browser printing
- [paper reading notes] a multilayered informational random walk for attributed social network embedding
- Coding style: SSM environment in MVC mode, code hierarchical management
- Hong Kong listed companies transfer cards to acquire 42.5% equity of chuangxinzhong and plan to speed up the distribution of marketing services
猜你喜欢
如何看待阿里云成立新零售事业部？
What can I do if I can't register didi? How to deal with it?
The high pass snapdragon 875 has won the title of Android processor, but the external 5g baseband has become its disadvantage
大专学历的我工作六年了，还有机会进大厂吗？
delete、truncate、drop 有什么区别，误删数据怎么办
推动中国制造升级，汽车装配车间生产流水线 3D 可视化
csdn bug6：待加
编码风格：Mvc模式下SSM环境，代码分层管理
MultiBank Group宣布创纪录的财务业绩，2020年前三季度毛利达到9,400万美元
Farfetch、阿里巴巴集团和历峰集团结成全球合作伙伴关系，将加速奢侈品行业数字化进程
随机推荐
编码风格：Mvc模式下SSM环境，代码分层管理
Commodity management - merge purchase demand into purchase order
Farfetch、阿里巴巴集团和历峰集团结成全球合作伙伴关系，将加速奢侈品行业数字化进程
JS solves the problem of automatic pagination in browser printing
想花钱速学互联网行业，大概花两三个月的时间，出来好找工作吗
The high pass snapdragon 875 has won the title of Android processor, but the external 5g baseband has become its disadvantage
上线1周,B.Protocal已有7000ETH资产!
[论文阅读笔记] RoSANE, Robust and scalable attributed network embedding for sparse networks
Coding style: SSM environment in MVC mode, code hierarchical management
Experiment 2
Seam engraving algorithm: a seemingly impossible image size adjustment method
Promote China manufacturing upgrade, 3D visualization of production line in automobile assembly workshop
刷题到底有什么用？你这么刷题还真没用
Use call, apply and bind to solve the annoying this in JS, this in event binding and parameter passing
[paper reading notes] large scale heterogeneous feature embedding
csdn bug10：待加
CCR炒币机器人：新冠肺炎加速了监管机构对CBDC的兴趣
gnu汇编语言使用内联汇编 扩展asm
C++ STL容器篇
从大专生到蚂蚁金服CTO，他写下“支付宝”第一行代码：逆风的方向，更适合飞翔！...