Current and voltage acquisition module DAM-6160

​DAM模块全新升级更换新版外壳,安装简易;使用标准的modbusRTU通信协议,可以对接多种串口软件,应用广泛,通信简单方便,新添加模块做主站,自定义读取,满足各种需求,添加数据导出功能,实用性更加强大.内置双看门狗,不死机,稳定运行.

​提供C#,西门子PLC,三菱PLC,欧姆龙PLC,台达PLC,威纶通触摸屏通信实例demo.并提供模块调试助手

DAM模块是全新一代基于嵌入式系统的模块式数据采集器,采用标准DIN35导轨安装方式,现场安装简单,使用灵活;应对各种现场应用.Module configuration hasRS485/RS232接口,方便与PC或PLC通信,可单独与PC或PLC通信,也可以与多个485模块组网使用.

DAM-6160Analog input terminal,可采集16Single-ended analog signals;模块采用高性能12位AD芯片,Through the circuit and special software algorithm,Finally collected measurement precision is better than that of±0.2%.Applicable to the acquisition of industrial field a variety of voltage and current signals.

DAM-6160USES the advanced magnetic isolation technique,The effective protection of data acquisition speed、Reliable and safe.

产品特性：

◆嵌入式实时操作系统
◆模拟输入通道：16路单端
◆The analog input signal range：	20mA,	+5V,
	+10V,	+24V
◆AD转换分辨率：12位
◆测量精度：±0.2%（典型值）
◆转换速率：60次/秒（全通道）
◆宽供电范围：DC 9～30V
◆地址/Baud rate can be configured by the user
◆支持Modbus RTU协议
◆Support module initiative to send data model ◆RS485/RS232隔离通信
◆±15KV ESD保护
◆Three-terminal isolation pressure：电源/通信/Analog input between≥1500V AC
◆工作温度范围：-40℃～80℃
◆工业级ABS阻燃外壳,标准DIN35导轨

功能配置：

模块型号	DAM-6160
AD(12bit)	16路
RS232	支持
RS485	支持

 输入输出隔离

产品针对工业应用设计：通过DC-DC变换,实现测量电路和主控电路电源隔离;At the same time, the control unit and communication unit adopts photoelectric isolation technology to realize electrical isolation,To achieve the power supply、通讯、The purpose of collecting three-terminal isolation;有效保障数据采集Reliable and safe.

 通信隔离

产品采用RS485/232隔离电路,Will be isolated from communication with system alone,Eliminate common-mode interference between communications equipment.

 浪涌保护

模块配有瞬态抑制电路,能有效抑制各种浪涌脉冲,Protection module and reliable work under harsh environment.

​DAM-6160Analog input for single-ended input,All simulation module to(AGND)All together;AGNDIs the module all analog signal input fields,In order to improve the module precision,Please try to nearby ground.

DAM系列模块RS232接口为标准RS232接口,Comply with the relevant specification,如图所示,串口的2脚连接DAM模块的TX,串口的3脚连接DAM模块的RX,串口的5脚连接DAM模块的232GND.

​DAM-6160Module communication pattern is often primarily from the pattern（一问一答模式）;The host through the communication interface to send commands to the module,Module after receives the correct order to make corresponding response.

DAM-6160Can also through the command sets the module to module active mode（Module initiative to send data to the host）,Time interval can be set by the user,Take the initiative to send data time range is：100～999999mS.This pattern can not be applied to many module network work,Otherwise will cause the bus conflict.

 通信地址

Module communication address range as01～FF(1～255),Factory Settings module address as01;Module address can need according to the site by the user through the command to change,The specific methods refer to the corresponding command.

 通信速率

模块RS232/RS485支持波特率：1200bps、2400bps、4800bps、9600bps、19200bps、38400bps、57600bps、115200bps;Module factory default baud rate as9600bps,Module communication rate can need according to the site by the user through the command to change,Specific methods see configuration instructions

 通信协议

DAM模块支持Custom-ASCII协议(自定义的ASCII协议),用户可以通过简单的ASCIICommand convenient read measurement data and configuration module parameters,Such as the configuration address（0x01～0xFF）、波特率.

 Modbus RTU协议

Module supports industry standardModbus RTU协议,可以工作于Modbus从站状态.可以实现与多种品牌的PLC、触摸屏、Industrial PC andPC进行通信.