How to install win7 on AMD Ruilong CPU A320 series motherboard

Recently, due to the newly purchased main computer Mac Hardware failure is returned to the factory for replacement , You have to use a spare desktop ！ As a result, the system actually hung up because it hadn't been powered on for too long , All normal functions such as downloading files are unavailable , I have no choice but to reinstall the system , As a result, I tossed about for most of the day , Either blue screen error reporting or black screen error reporting ！ Because the main board installation system of Yilong series is a little cumbersome , Therefore, this article is published for record ！ Because I reset it when I reinstalled the system bios Setting causes factory reset , so ghost It needs to be brushed before the system bios It is the latest version, or an error will be reported on the blue screen ！ Then prepare a USB drive , Now the startup disk making tool needs to pay attention to downloading the installed version , Otherwise, an error will be reported on the black screen ！ Then the system goes to the system home to download win764 Bit system and above ,7 The following systems cannot be installed , must do 64 Bit system 32 Bit cannot be installed , I haven't tried Baidu to say so , Those who like to toss can have a try ！ After the startup disk is successfully made, it is now ready to brush the system , First, find the drive disc of the motherboard , Insert the CD-ROM drive and copy the drive files to the boot disk , Then the computer starts up and enters bios Set parameters ： Turn off flash start 、 Turn on csm、csm Compatibility set to traditional （win7 The above setting is uefi）、 The hard disk mode is set to ahci Pattern , Then save and restart ！ Insert the boot disk , Enter the Startup menu and select startup disk , At this point, enter the startup disk menu , Choose to enter pe, Here's a point to note ️ I made fourorfive startup disks before entering pe There was an automatic restart problem while waiting , The five plates are no exception ！ The production tools are old peach 、 Chinese cabbage 、 Old cabbage 、 Computer shop 、 Optimal startup , After the query, it is found that you only need to enter pe Keep pressing... While waiting F8 You can force automatic restart to be disabled , Successful entry pe Open the partition tool first after , Delete the damaged system disk and re create the partition , Remember the system disk , Don't touch the data disk ！ Then open pe Installation tools , Select... In the boot disk gho Perform system installation , Note that you cannot restart during installation , You should always follow the page and click Cancel to restart , If you restart, you need to repeat the previous operation ！ Pay attention ️ Very critical steps , Open the installed system and enter windows\system32\drivers find rcraid.sys The file backs him up to a disk other than the hard disk system disk , Open the installation tool again , choice gho install , The installation drive letter must be the same as that of the last installation , Check inject USB3.0 drive , Check the injection specified drive , OK, you will go to the next step to select the driver file , Select the motherboard driver that was previously backed up to the boot disk, and then start the installation , You should always pay attention to the interface and be careful not to restart , You need to cancel the restart , Otherwise, restart will occur windows Black screen error code that cannot be started . Cancel the restart and enter the previous backup rcraid.sys Disk , Put the file back to the path of the previous copy , Because the injection driver will change this file , OK, now you can restart , But boot repair is required before restarting , Otherwise, a black screen will appear error Report errors , OK, now you can restart . Restart and enter bios, Get into boot The menu changes the first startup disk to the system disk , This operation is not necessary if there is only one disk , Because I have eight plates , If you do not do this, you will not be able to enter the system normally ！ Before that, unplug the startup disk , Otherwise, the boot disk may be accessed . OK, now normally enter the system initialization installation page , There is no wrong report , Wait for installation to complete , After installation, download the driver wizard to detect whether there are abnormal drivers , If the graphics card is abnormal, go to amd Do not install the graphics card driver on the driver wizard , There will be loss of function , So far, the installation is complete