A comprehensive and detailed explanation of static routing configuration, a quick start guide to static routing

Operation steps

Configure the IP Address

To configure Router_1 Of GE0/0/0 Interface, for example , Other interface configurations are similar , Don't repeat .

a、 Pictured 2 Shown , Choose in turn “ Wan interconnection > Ethernet Interface ”, Get into “ Ethernet Interface ” Interface .

chart 2  Ethernet interface

b、 stay “ List of Ethernet interfaces ” in , single click “GigabitEthernet0/0/0” Of the line , To configure GE0/0/0 Of IP Address , Pictured 3 Shown .

chart 3  To configure GE0/0/0 Of IP Address

c、 single click “ determine ”, complete Router_1 Upper interface GE0/0/0 Of IP Address configuration .

Same way , To configure Router_1 Upper interface GE0/0/1,Router_2 and Router_3 Of each interface on IP Address .

Router_1 Upper interface GE0/0/1 Of IP The address information is as follows .

• “IP Address ” by “10.1.4.1”;“ Subnet mask ” by “255.255.255.252”.

Router_2 Of each interface on IP The address information is as follows .

• “ The name of the interface ” choice “GigabitEthernet0/0/0”;“IP Address ” by “10.1.2.1”;“ Subnet mask ” by “255.255.255.0”.
• “ The name of the interface ” choice “GigabitEthernet0/0/1”;“IP Address ” by “10.1.4.2”;“ Subnet mask ” by “255.255.255.252”.
• “ The name of the interface ” choice “GigabitEthernet0/0/2”;“IP Address ” by “10.1.4.5”;“ Subnet mask ” by “255.255.255.252”.

Router_3 Of each interface on IP The address information is as follows .

• “ The name of the interface ” choice “GigabitEthernet0/0/0”;“IP Address ” by “10.1.3.1”;“ Subnet mask ” by “255.255.255.0”.
• “ The name of the interface ” choice “GigabitEthernet0/0/1”;“IP Address ” by “10.1.4.6”;“ Subnet mask ” by “255.255.255.252”.

To configure Router_1 The default route for

a、 Pictured 4 Shown , In turn, click “IP Business > route > Static routing configuration ”.

chart 4  Static route configuration interface

b、 stay “IPv4 Static routing configuration table ” in , single click “ newly build ”, To configure Router_1 The default route for , Pictured 5 Shown .

chart 5  To configure Router_1 The default route for

c 、 single click “ determine ”, complete Router_1 Default routing configuration .

Same way , To configure Router_2 and Router_3 Routes to different network segments .

Router_2 The routing configuration information to different network segments is as follows .

• “ Purpose IP Address ” by “10.1.1.0”;“ Subnet mask ” by “255.255.255.0”;“ Next jump ” by “10.1.4.1”.
• “ Purpose IP Address ” by “10.1.3.0”;“ Subnet mask ” by “255.255.255.0”;“ Next jump ” by “10.1.4.6”.

Router_3 The default routing information of is as follows .

• “ Purpose IP Address ” by “0.0.0.0”;“ Subnet mask ” by “0.0.0.0”;“ Next jump ” by “10.1.4.5”.

Verify configuration results

# When the configuration is complete , In turn, click “IP Business > route > Routing table ”, You can check the router IP Routing table information . With Router_1 For example , See the following figure 6 Configuration results shown .

chart 6  Configuration result

PC_1 Can and PC_2 and PC_3 To communicate with each other .

Configuration considerations

• Ensure that the interconnection interface addresses of the two routers are configured in the same network segment , And it can be interconnected normally .
• Configure... On each host IP Address and IPv4 Default gateway .
• If the purpose IP The address and mask are 0.0.0.0, The configured route is the default route .
• If the outgoing interface type is non-point-to-point , Then you must specify the next hop address .
• The next hop and exit interfaces cannot be empty at the same time .

Delete static route

1、 choice “ senior > IP Business > route > Static routing ”, Enter the static routing interface as shown in the figure 1 Shown .

2、 stay “ Static route list has been set ” in , Select the static route to delete , single click “ Delete ”. In the pop-up screen , single click “ determine ” Delete the selected static route .