Hcip day 16

MPLS VPN To configure

establish VRF Space

[r2]ip vpn-instance a

[r2-vpn-instance-a]

To configure VRF Space

[r2-vpn-instance-a]route-distinguisher 100:100 --- To configure RD value

[r2-vpn-instance-a-af-ipv4]vpn-target 100:1 export

extcommunity --- Configure outbound RT

[r2-vpn-instance-a-af-ipv4]vpn-target 100:2 import

extcommunity --- Configure inbound RT

[r2-GigabitEthernet0/0/0]ip binding vpn-instance a ---- Speak interface binding

Set to the corresponding VRF In the space

[r2]display ip routing-table vpn-instance a ---- see VRF Spatial routing table

[r2]ping -vpn-instance a 192.168.2.1

[r2]ip route-static vpn-instance a 192.168.1.0 24

192.168.2.1 ---- Configure static routing in the spatial routing table

MP-BGP Jianlin

[r2]bgp 1

[r2-bgp]router-id 2.2.2.2

[r2-bgp]peer 4.4.4.4 as 1

[r2-bgp]peer 4.4.4.4 connect-interface LoopBack 0

[r2-bgp]ipv4-family vpnv4

[r2-bgp-af-vpnv4]peer 4.4.4.4 enable

MP-BGP Route Publishing

[r2-bgp]ipv4-family vpn-instance a

[r2-bgp-a]import-route direct

[r2-bgp-a]import-route static

[r2]display bgp vpnv4 vpn-instance a routing-table ---- Look inside the space BGP surface

[r2]display fib vpn-instance a --- Look inside the space FIB surface

[r2]rip 1 vpn-instance a ---- stay VRF Start in space RIP process

[r2-rip-1]v 2

[r2-rip-1]network 192.168.2.0

[r4]ospf 2 vpn-instance b router-id 4.4.4.4 ---- stay VRF Start in space

ospf process

The three-tier architecture of the enterprise --- Suggestions for building an enterprise network

Park ---- factory , The government authority , Office buildings , campus , Park, etc , The networks built in these public places to realize data exchange can be called campus networks . Different campus networks may have different emphases .

Wireless is always the last kilometer of wired

Wireless connections need to rely on wireless devices that can transmit and receive wireless signals , And these devices

Finally, it also needs to be connected to the network through cable .

AP --- Wireless access point

WLAN --- WLAN ---- In a broad sense, it refers to radio waves , laser , Infrared

And so on to replace part or all of the transmission media of the wired LAN .

Wireless networks are inherently flawed ：

1, Poor penetration of wireless signals

Wireless uses Ethernet Technology --- Frequency division ---- And the civil wireless network uses

Data transmission in low frequency band , The congenital defect of low frequency band is penetrability

Bad .

2, The transmission rate of wireless network is related to the signal strength , and , His transmission rate refers to two-way

rate

1000 / 8 * 0.85 = 106.25

200 / 8 / 2 * 0.85 = 10.625

3, Wireless network transmission efficiency is low , Slower

Conflict domain ： The scope of the conflict --- A hub is in a conflict domain

CSMA/CD --- Carrier sense multiple access / Conflict detection technology

WLAN is equivalent to in the same conflict domain , And wireless technology is the way to solve the conflict

The method is to use CSMA/CA

CSMA/CA --- Carrier sense multiple access / Conflict avoidance techniques --- Its transmission efficiency

Than CD Lower technology

The wireless device cannot detect the conflict. The reason --- Dynamic range of wireless signal strength

It's very big , Often the received signal strength may be much less than the sent signal strength ,

This makes it difficult to detect conflicts （ It can increase hardware performance and improve strength ）

CA Technology to avoid conflict ：

1, When no message is sent in the listening range , Don't send signals directly , It is ,

Set yourself a random timer first .

2,CSMA/CA The technology adopts stop flow control .

Access layer ---- The main purpose is to connect the terminal equipment to the network , Provide access port ---- Generally, layer-2 switches are used （ rely on MAC Address table realizes two layer forwarding ）

Convergence layer ---- The main purpose is to gather the traffic collected by the access layer , Generally, three-layer switching is adopted

machine ---- It has a layer-2 interface similar to that used by ordinary layer-2 switches , It also has a three-tier interface similar to that used by routers or computers . The biggest difference between the second floor opening and the third floor opening is whether there is IP Address .

The layer-3 switch can pass through MAC Address table realizes two layer forwarding , Three layer forwarding can also be realized through routing table .

The core of the three-tier architecture of enterprise network --- redundancy ---- Backup

1, Line redundancy

2, Equipment redundancy

3, Gateway redundancy

4,UPS redundancy ---- UPS --- Uninterruptible power supply ---- Ensure that the power supply of enterprise equipment reaches 6 individual 9 The usability of .99.9999%

A real three-tier architecture , There must be redundancy .

Core layer --- The main function is to complete the rapid forwarding of data between public and private networks . ---- Generally, the router is selected as the core layer device .

VLAN

V --- fictitious

LAN --- LAN ---- Networks with small geographical coverage

MAN --- Metropolitan area network

WAN --- Wide area network

LAN --- Broadcast area

VLAN --- Virtual LAN --- After the switch and router work together , Put the original one

The broadcast domain is logically divided into multiple ;

First step ： establish VLAN

[Huawei]display vlan --- see VLAN Information

VID --- VLAN ID ---- Distinguish and calibrate different VLAN ---- IEEE Organize and issue

802.1Q The standard requires --- VID Must be by 12 Bit binary structure . Value range 0 -4095,0 and 4095 Is the reserved number , therefore , The available value range is 1 - 4094

[Huawei]vlan 2 --- establish VLAN

[Huawei]vlan batch 4 to 100 --- Batch creation VLAN

[Huawei]undo vlan batch 4 to 10 --- Batch deletion VLAN

The second step ： Put the interface into VLAN

VID Configure the interface mapped to the switch , Realization VLAN Division --- First floor VLAN/ Physics VLAN

VID Configure the mapping to data MAC Address , Realization VLAN Division --- On the second floor VLAN

VID Configure the type fields mapped to the data , Realization VLAN Division --- Three layers VLAN

VLAN Can also be based on IP Address division , It can even be done according to the strategy VLAN Divide .

802.1Q Standard design VLAN The label of , By 4 Bytes make up , It includes 12 Bit VID, Used to distinguish between different VLAN Of traffic . And add this label to Ethernet Ⅱ Type frame

Source MAC Between address and type fields .

802.1Q The standard stipulates , Frames with labels are called tagged The frame or 802.1Q frame , Frames without labels are called untagged frame

According to this feature , We call the link between the switch and the computer ACCESS link , also ,ACCESS The interface on the switch side of the link is called ACCESS Interface .ACCESS The link can only pass through untagged frame , also , These frames can only belong to the same VLAN.

We call the link between switches trunk link ,trunk The interfaces at both ends of the link are called trunk Interface .trunk The link is allowed to pass through tagged frame , And these frames can belong to multiple VLAN.

The third step ： To configure trunk main rd

The second step is configuration

[sw1-GigabitEthernet0/0/1]port link-type access

[sw1-GigabitEthernet0/0/1]port default vlan 2

[sw1]port-group group-member GigabitEthernet 0/0/3

GigabitEthernet 0/0/4

[sw1-port-group] --- Create an interface group

Step 3 configuration

[sw1-GigabitEthernet0/0/5]port link-type trunk

[sw1-GigabitEthernet0/0/5]port trunk allow-pass vlan all

hybrid --- Hybrid interface

[sw1]display port vlan active

Link Type ---- Huawei equipment , The default interface type of all interfaces is hybrid

PVID --- Huawei gives every interface , You need to configure a PVID, That is, the interface belongs to VID. All interfaces have not been changed PVID Default PVID The value is 1.

Huawei system regulations ： All data entering the switch through the interface , All interfaces must be marked PVID The label of , in other words , All data inside the switch is labeled .

ACCESS Interface

1, When ACCESS The interface received a message from the link untagged After the frame , Swap opportunities add... To this frame VID Interface for PVID yes tag, Then look at this VID Whether it is in the Allow list , If in , Then for what you get tagged Forward frames .

2, When tagged The frame goes from other ports of the switch to one ACCESS After a mouth , Then the exchange opportunity checks the data in this frame tag Of VID Whether you are in your allow list , If in , Will tag After stripping, it will be forwarded from the link , If not , Then discard .

3, If ACCESS The interface received a message from the link tagged After the frame , Then you can directly see the label of the data belongs to VID Whether you are in your allow list , Forward in , No longer discard .

trunk Interface

1, When trunk The interface received a message from the link untagged frame , The switch first adds a... To the data frame VID by PVID Of tag, Then according to VID View the Allow List , If there is , Then forward , without , Then discard ;

2, When one tagged The frame goes from other ports of the switch to one trunk After the port , If tag Of VID stay trunk In the allowed list of , Then forward （ If VID and trunk Interface PVID Phase at the same time , The label needs to be peeled off when transferring out , If not PVID The same label , Then directly transfer out ）, If not , Throw away ;

3, If trunk The port receives a message from the link tagged After the frame , View tag Medium VID, If in the Allow List , Then forward , be not in , Then discard ;

Different interfaces have different modification permissions when customizing the forwarding table .

ACCESS Modify permission of interface

You can modify PVID, You can also modify the Allow List （ however , The Allow list can only have one

VID, And it has to be with PVID identical ）, The export packaging method is only non packaging .

trunk Modify permission of interface

You can modify PVID, You can also modify the Allow List , The Allow list can be set to more than one VID,

Export packaging is only packaging （ and PVID same VID If it is in the Allow list, it is fixed as no label ）

[sw1-GigabitEthernet0/0/5]port trunk pvid vlan 2 ---- Sure

modify trunk Of PVID

hybrid --- Modify permission of hybrid interface

You can modify PVID, You can also modify the Allow List , There can also be more than one allowed list

VID, The packaging method can also be modified .

[sw1-GigabitEthernet0/0/1]port link-type hybrid

[sw1-GigabitEthernet0/0/1]port hybrid pvid vlan 2 --- modify hybrid Interface PVID

[sw1-GigabitEthernet0/0/1]port hybrid untagged vlan 2 3 4 --- Define allow list