H3C S5820V2_ Upgrade method after stacking IRF2 of 5830v2 switch

1.   Preparations before upgrading 
   

l Prepare the software version file required for the upgrade S5820V2_5830V2-CMW710-R2208P01.ipe;

l adopt ftp or tftp Upload the version file to slot1 and slot2 Of flash:/ Under the table of contents ;

1.1. Upgrade first Master equipment , Upgrade again Slave step
step

Job content

1

First delete the configuration about mad Detected configuration

[ASW-T06-I03.CM3]interface Bridge-Aggregation 100

[ASW-T06-I03.CM3-Bridge-Aggregation100]undo mad enable

2

take slot 1 All service ports in the device shutdown, And save the configuration

[ASW-T06-I03.CM3]interface range Ten-GigabitEthernet 1/0/1 to Ten-GigabitEthernet 1/0/48

[ASW-T06-I03.CM3-if-range]shutdown

<ASW-T06-I03.CM3>save

The current configuration will be written to the device. Are you sure? [Y/N]:y

Please input the file name(*.cfg)[flash:/config.cfg]

(To leave the existing filename unchanged, press the enter key):

flash:/config.cfg exists, overwrite? [Y/N]:y

Validating file. Please wait…

Saved the current configuration to mainboard device successfully.

Slot 2:

Save next configuration file successfully.

3

Appoint boot-loader, Restart upgrade slot1 Equipment to R2208P01 edition ; Restart the slot 1 Pass immediately after Slot2 Of Console mouth , stay Slot 2 On the device shutdown all IRF port .

<ASW-T06-I03.CM3>boot-loader file flash:/S5820V2_5830V2-CMW710-R2208P01.ipe slot 1 main

<ASW-T06-I03.CM3>reboot slot 1

Start to check configuration with next startup configuration file, please wait…DONE!

This command will reboot the specified slot, Continue? [Y/N]:y

Now rebooting, please wait…

%Jan 3 04:00:55:522 2011 ASW-T06-I03.CM3 DEV/5/BOARD_REBOOT: Board is rebooting on Slot 1.

<ASW-T06-I03.CM3>sys

[ASW-T06-I03.CM3] interface range FortyGigE 2/0/49 to FortyGigE 2/0/52

[ASW-T06-I03.CM3-if-range]shutdown

Be careful ：

1、 Never reboot Wrong slot number ,slot 1！ Remember ！

Need to pass console Connect to Slot 2 On ,shutdown IRF port , This operation requires fast ,reboot Immediately after .

4

Console Connect to Slot 1 On the device , Upgrade the completed Slot 1 All the service ports in the device undo shutdown open .

[ASW-T06-I03.CM3]interface range Ten-GigabitEthernet 1/0/1 to Ten-GigabitEtherne

t 1/0/48

[ASW-T06-I03.CM3-if-range]undo shutdown

Be careful ：

Do not save the configuration here !

5

Console Connect to Slot 2 On the device , Specify the startup file as R2208P01, restart slot 2 Upgraded version ;、

<ASW-T06-I03.CM3>boot-loader file flash:/S5820V2_5830V2-CMW710-R2208P01.ipe slot 2 main

<ASW-T06-I03.CM3>reboot slot 2

Start to check configuration with next startup configuration file, please wait…DONE!

Current configuration may be lost after the reboot, save current configuration? [Y/N]:N

This command will reboot the specified slot, Continue? [Y/N]:Y

Be careful ：

Whether to save the configuration pops up here , Be sure to choose N

6

Check whether the stack is successful , Whether the aggregation group status is normal , Whether the configuration is complete

7

Restore previously deleted mad Detected configuration , And save the configuration .

[ASW-T06-I03.CM3]interface Bridge-Aggregation 100

[ASW-T06-I03.CM3-Bridge-Aggregation100] mad enable

1、 The configuration will not be lost after upgrading ;

2、 During the upgrade , In addition to 2、7 Step , There is no need to save the configuration in other steps ;

3、 Intermediate state of upgrade , The versions of the two devices are inconsistent , When all service ports are opened , because IRF Split the rear axle MAC The address is the same , therefore LACP Neighbors and these two S58V2 Two devices cannot be distinguished when connected , The port status will be set to Select state ;

4、 Upgrade to R2208P01 Then apply the patch version S5820V2_5830V2-CMW710-R2208P01H03.