H3C HCl MPLS layer 2 dedicated line experiment

HCL The simulator is strange , occasionally 2 Routers are configured with the same network segment IP In the future PING no , You have to restart the router to PING through .

Experimental Topology ：
IGP Routing OSPF and ISIS Do route penetration , utilize MPLS Realization LDP The whole network is interconnected , Routers on both sides are established AC

The router LOOP Router id Set up ：
[H3C]int loop 0
[H3C-LoopBack0]ip ad
[H3C-LoopBack0]ip address 1.1.1.1 32
[H3C-LoopBack0]q
[H3C]router id
[H3C]router id 1.1.1.1
3 Routers with similar configurations
R1 Router IP and OSPF Set up
[r1]int g0/0
[r1-GigabitEthernet0/0]ip ad
[r1-GigabitEthernet0/0]ip address 10.0.0.1 30
[r1-GigabitEthernet0/0]qu
[r1]ospf router-id 1.1.1.1
[r1-ospf-1]area 0
[r1-ospf-1-area-0.0.0.0]network 0.0.0.0 0.0.0.0
R1 MPLS To configure
[r1]mpls lsr-id 1.1.1.1
[r1]mpls ldp
[r1]l2vpn enable
[r1]int g0/0
[r1-GigabitEthernet0/0]mpls enable
[r1-GigabitEthernet0/0]mpls ldp enable
R3 OSPF ISIS MPLS To configure
[r3]ospf router-id 3.3.3.3
[r3-ospf-1]area 0
[r3-ospf-1-area-0.0.0.0]network 0.0.0.0 0.0.0.0

[r3]mpls lsr-id 3.3.3.3
[r3]mpls ldp
[r3-ldp]qu
[r3]l2vpn enable

[r3]int g0/1
[r3-GigabitEthernet0/1]mpls enable
[r3-GigabitEthernet0/1]mpls ldp enable
[r3]int g0/0
[r3-GigabitEthernet0/1]mpls enable
[r3-GigabitEthernet0/1]mpls ldp enable
[r3]isis 100
[r3-isis-100]network-entity 49.0001.0100.1100.0000.00
[r3-isis-100]is-level level-2
[r3-isis-100]qu
[r3]int g0/1
[r3-GigabitEthernet0/1]isis enable 100
[r3]int loop 0
[r3-LoopBack0]isis enable 100

R2 ISIS MPLS To configure
[r2]isis 100
[r2-isis-100]network-entity 49.0001.0010.0120.0000.00
[r2-isis-100]qu
[r2]int loop 0
[r2-LoopBack0]isis enable 100
[r2-LoopBack0]int g0/0
[r2-GigabitEthernet0/0]isis enable 100

[r2]mpls ls
[r2]mpls lsr-id 2.2.2.2
[r2]l2vpn enable
[r2]mpls ldp

[r2]int g0/0
[r2-GigabitEthernet0/0]mpls en
[r2-GigabitEthernet0/0]mpls ldp en

R3 Routing in

[r3-isis-100]address-family ipv4（ It took a long time to find out HCL You need to add this command to introduce routing ）
[r3-isis-100-ipv4]import-route ospf

[r3-ospf-1]dis th
ospf 1 router-id 3.3.3.3
import-route isis 100
area 0.0.0.0
network 0.0.0.0 255.255.255.255

R1 LSP Established
R1 establish AC
[r1]xconnect-group l2vpn
[r1-xcg-l2vpn]connection ldp
[r1-xcg-l2vpn-ldp]ac interface GigabitEthernet 0/1
[r1-xcg-l2vpn-ldp]peer 2.2.2.2 pw-id 100

R2 establish AC
[r1]xconnect-group l2vpn
[r1-xcg-l2vpn]connection ldp
[r1-xcg-l2vpn-ldp]ac interface GigabitEthernet 0/1
[r1-xcg-l2vpn-ldp]peer 1.1.1.1 pw-id 100

AC passageway UP

Configuration completed PING Connect to end-to-end equipment