Taiwan Xinchuang sss1700 latest Chinese specification | sss1700 latest Chinese specification | sss1700datasheet Chinese explanation

                                                          Taiwan Xinchuang SSS1700 The latest version of the Chinese manual |SSS1700 The latest Chinese specification |SSS1700 datasheet Chinese explanation

 

            SSS1700 It's Taiwan Xinchuang SSS Following SSS1629/SSS1630 A new USB Audio control chip .SSS1700 comparison SSS1629 and SSS1630, It has the following advantages ：
1. Whole USB Audio design circuit without capacitor output , Chip built in 12MHz Crystal oscillator , Reduce peripheral devices , The whole scheme BOM Cost reduction , The size of board and frame can be made smaller .
2.SSS1700 The sound quality of the chip has been greatly improved , Support 96 KHz 24 Bit sampling rate and external audio codec （24 position /96 KHz I2S Input and output ）, Compare SSS1629 Support only 48HZ 16 Bit sampling rate , You can give user Provide a better auditory experience .
3.SSS1700 The overall bottom noise of the chip is greatly reduced , The average bottom noise of the chip is about 60DB about .
4.SSS1700 Support 3.5MMM 4 Segmental American standard / British standard automatic switching , Broaden the applicable scenarios , The switching circuit in the design process is reduced .
5.SSS1700 Support Mciro USB、Type-C 3.1 Interface ,lightning Interface , Headphones can be realized 、 Microphone function . Call support 、 Hang up 、 Volume increase and decrease function .
One .SSS1700 chip Product features ：

accord with USB standard v2.0 Run at full speed

 

accord with USB Audio equipment class specification v1.0

 

Support 44.1KHz/48KHz/96KHz、16 position /24 Bit sampling rate （EEProm Option ）

 

Embedded digital mixer , After power on, the default mixer is silent （ Operating system control ）

 

When setting sheet ADC when , Two DAC All channels are related to the order ADC Data mixing

 

When setting stereo ADC when ,L-ch DAC And L-ch ADC Data mixing ,R-ch DAC And R-ch ADC Data mixing

 

Power mode setting ROM Options （USB Bus power supply 100mA： Default or 500mA To configure ）

 

The default support 16 and 24 position ,48KHz Sampling rate ADC and DAC

 

Embedded earphone driver , the height is 16 Ohmic load drive

 

ADC Line input to DAC Output data path options

 

be used for 16/24 Bit codec DAC/ADC（EEPROM Option ） Embedded in I2S Interface （ Lord / Slave mode ）

 

be used for 16/24 Bit codec DAC/ADC（EEPROM Option ） Embedded in SPDIF I / O interface

 

Embedded crystal free on-chip oscillator

 

Support USB Hang up / Recovery mode

 

be used for USB Embedded interface USB Transceiver

For Headphone Function ,USB The audio function topology has 2 Two input terminals ,2 Two output terminals ,（1 A mixer unit ）,（1 A selector unit ） and （3） Functional units （ Some units can be through ROM Code options enable ）

 

Support a control endpoint 、 A synchronous output endpoint 、 A synchronous input endpoint 、 An interrupt input endpoint （HID Use interrupt input and control output ）

 

Standby zero bandwidth setting , Used to release when the device is inactive USB Playback bandwidth on the bus

 

The volume goes up 、 volume down 、 Play mute 、 Recording mute 、 Next track 、 Previous track 、 Stop and play / Pause pin , For users to directly control

 

The volume goes up 、 volume down 、 Play mute 、 Next track 、 Previous track 、 Stop and play / Suspend support

 

Two wire serial bus （I2C Bus ） For external use MCU Control the whole EEPROM Space can pass through MCU visit

 

For host control synchronization USB HID

 

External serial port EEPROM（24C02~24C16） Interface , For customer specific USB video 、PID、 Product string 、 Serial number 、 Default gain 、 Default EQ Set up 、 Play / Logging enabled and other options

 

EEPROM The write function passes HID Or the specific requirements of the supplier , Provide convenience for mass production

 

Preloaded VID、PID And product strings and design options to set priorities ：i） external EEPROM ii） The embedded ROM

 

Customer specific requests and new virtual registers （10XX\u 10XX; among XX It can be set by register write back and read back , To verify ） For software protection

 

GPIO and MCU The interface register passes through HID read / Write

 

True headphone amplifier solution

 

Support CTIA/OMTP Automatic switch TRRS Audio jack （EEPROM Option ）

 

Support AD Key detection （EEPROM Options ）

 

Support RGB LED（EEPROM Option ）

 

Support HID keyboard （EEPROM Option ）

 

Support IIC Initial external codec （EEPROM Options ）

 

The embedded 1.2V POR

 

The embedded 5V to 3.3V（250mA Capacity ） and 3.3V to 1.2V Regulator , For a single external 5V Power Supply

 

Embedded rotary encoder interface for volume control （EEPROM Option ）

 

1.2V Digital core and audio PLL operation 、3.3V USB PLL Operation and ADC/DAC operation

 

Two 、SSS1700 Electrical parameters and parameter setting methods

1. Absolute maximum rating

 

2. DC characteristics

 

3.  Communication characteristics

Headphone output

 

Microphone input characteristics

 

4. Pin description

 

48 foot LQFP/QFN Pin output diagram of

 

36 foot QFN Pin output diagram

 

 

Pin list

 

Play 、 Recording and function options

 

 

Insert path selection function options

 

 

5. Block diagram and description

 

USB The default setting of the line in mode

 

 

6. Automatic gain control （AGC）

 

SSS1700 have AGC（ Automatic gain control ） function . It can automatically adjust ADC Output range , send ADC The output of is kept in a stable range .AGC The control schematic diagram is as follows , The gain adjustable range is -23dB~+40dB, Each level 1dB Adjustable .

 

 

AGC Parameter settings can be set in EEPROM Set in . Control characteristics include time stability 、 Error range 、 Active way 、 Retention time 、 Speed regulation, etc , These parameters need to be set separately . Its operation diagram is as follows: ：

 

 

 

AGC The goal of tuning is to be within two blue lines . As shown in the previous figure , The signal is below the blue line interval , be AGC The amplifier adjusts the signal to the blue line range . Similarly , In the picture , The signal exceeds the blue interval , then AGC Reduce the signal to the blue range .

 

7. Multifunction buttons （4 key ）

 

SSS1700 Most support 4 Multiple function keys . adopt EEPROM Set up , Each multifunction key can have up to four different button operation modes . The four different button operations are “ Short press ”、“ Short press... Twice in a row ”、“ Short press and long press ” and “ Long press ”.

 

Each multifunction key corresponds to a different control mode , To meet different functional requirements , So as to achieve the purpose of simplifying the number of keys . The setting diagram is as follows ：

 

Key input can be set from the following positions ： The function output can be assigned to ：

 

8.LED Lamp effect function

 

SSS1700 It has the function of stereo audio waveform gradient indicator . adopt EEPROM Set up , Up to six indication signals can be provided （L/R The difference between the , Share three indication signals for each channel ）. The indication signal can be connected to LED As an audio output gradient indicator . When the audio signal is zero ,LED It can be set as breathing lamp , To increase product diversity .

 

The following is the function diagram ： 

 

When setting the audio output indicator , It can be adjusted according to the required output range ; Each indicator signal can have 16 Make the recommended audio settings at two levels .

 

9. Five band equalizer

 

SSS1700 On the playback path 5 Equalization function of multiple frequency bands , Provide users with sound effect adjustment . These frequencies of the five band equalizer are fixed at 60Hz、300Hz、1.2KHz、3.6KHz and 12KHz. The gain of each frequency band can be set to +12dB~-∞dB, As shown below ：

 

 

Users can adjust a variety of sound effects according to their needs , The adjusted sound effect is stored in EEPROM in , You can use a single button to change different sound effects in a circular way , It also provides a single LED Indicating switch sound effect . By default ,SSS1700 Built in a subwoofer sound settings , therefore , There's no outside EEPROM Under the circumstances , There is still one EQ Voice conversion for users . Preset bass （ Subwoofer ） The sound settings are as follows ：

 

 

10.LQFP48（U6C）/QFN（Q6C） Typical application circuit of

 

 

11.QFN36（QCC） Typical application circuits

 

3、 ... and 、 Packaging information

 

LQFP 48 

  

 

QFN48

 

 

 

  QFN36